GrailAtlasAn independent mechanical watch reference
简体中文
Common#1 in familyOfficial press photos

Live pricing is coming soon. Get notified when it is available for this reference.

Movement tier: unclassified · caliber Lang & Heyne Cal. I: in-house manual-wind, 21,600bph, 50h PR; used in Friedrich; traditional German three-quarter plate, hand-finished in Dresden; extremely small production · 50h power reserve (2.1 days)
Medium-large: suits wrists 6.5 in+ (16.5 cm+)
39.5 mm case. Wears confidently on average to larger wrists. May overhang on slender builds.

Not yet rated

Community + OSINT signals haven’t landed for this reference yet. We don’t publish a rating against zero signal: the number would mean nothing. Editorial body + caliber + market value still surface above; ratings appear once the signal corpus does.

Search pre-owned listings

Chrono24
eBay (sold listings)
WatchBox

Authentication

The Friedrich II three-quarter plate chamfering must be hand-done and sharp under a loupe; Lang and Heyne produces fewer than 150 pieces per year, so verify the serial number before purchase.

Known issues in the market
  • Lang and Heyne produces fewer than 150 pieces annually; serial number provenance verification with the manufacturer is essential.
  • Hand-beveled chamfers on bridges are the authentication marker.
AreaWhat to checkWhat is correctRed flag
movementThree-quarter plate hand-beveled chamfersSharp hand-done chamfers on bridges; Dresden finishing standardMachine-polished chamfers; finishing does not meet Lang and Heyne standard
casebackThree-quarter plate Cal. I architectureCal. I three-quarter plate visible through caseback; manual-windNon-three-quarter-plate architecture; movement swap
dialDial quality and textDial surfaces and text consistent with Lang and Heyne production qualityDial inconsistencies; text irregularities; non-genuine dial
Common legitimate replacements
  • No standard service replacements; all components Lang and Heyne only.
Expert resources: Lang and Heyne direct for serial number verification; Dresden watchmaker network.

Authentication guide

Last reviewed June 2026

Provenance is the primary authentication tool for the Friedrich. Lang & Heyne produces approximately 30 to 50 watches per year from their Glashütte atelier; no replica exists at this production scale.

Known reproduction risks

toggle
LOW

No known replicas of the Friedrich. The watch is too low-volume, too technically demanding, and too well-documented by the community to support a viable counterfeit trade.

The risk here is misrepresented condition or undisclosed service, not a replica. Verify serial against Lang & Heyne atelier records and request full service paperwork.

Dial variants by era

toggle
EraDescriptionIdentifiers
2001 to presentSilver or off-white enamel dial with restrained applied typography. The name "LANG & HEYNE" is placed above center; "GLASHÜTTE I/SA" below the hour track. No clutter: the dial is about negative space and proportion.
  • Applied gold hour markers (baton or Roman depending on configuration)
  • Blued steel hands with a matte finish, not lacquered
  • Enamel surface shows slight depth under raking light; flat lacquer shows none

Service part flags

toggle
Hands

Original: Blued steel, hand-made to the atelier standard. The bluing is even and deep, without the flat or slightly purple cast of chemically blued replacements.

Replacement tells
  • Purple tint rather than deep true blue
  • Inconsistent finish between the hour and minute hand
  • Hands that do not sit close to the dial (spacing should be tight and uniform)
Caseback crystal

Original: Sapphire exhibition back showing the three-quarter plate movement with Glashütte stripes, swan-neck regulator, and blued screws.

Replacement tells
  • Replacement crystal with visible cement or improper gasket seating
  • Any obstruction to the view of the swan-neck spring

Case back markings

toggle
2001 to present
  • Serial number engraved on the movement plate, not the case
  • "LANG & HEYNE DRESDEN" on the movement
  • Case number stamped on the inner case back edge

Movement tells

toggle
  • The three-quarter plate covers most of the movement; Glashütte stripes run the full length under magnification.
  • The swan-neck regulator is hand-fitted and should contact the hairspring collar at the correct tension point, not jammed or sprung.
  • All screws are blued steel with polished, countersunk heads; bright screws indicate a replacement from a non-original source.
  • The barrel bridge and cock show hand-applied beveling; machine chamfers are a different width and angle.
  • Any service should be documented with the Lang & Heyne atelier or an authorized repairer; the production numbers are low enough that tracing service history is practical.
Sources: Lang & Heyne official site; WatchProSite — Glashütte independents forum.

You might also like

F.P. Journe Chronomètre Souverain Ref. CS-40-PT, silver dial, platinum case
F.P. Journe
Chronomètre Souverain
Ref. CS-40-PT
Vacheron Constantin Patrimony (manual-wind, ultra-thin) Ref. 81180/000G-9117, silver dial, gold-rose case
Vacheron Constantin
Patrimony
Ref. 81180/000G-9117
A. Lange & Söhne Datograph (first generation) Ref. 403.035, silver dial, platinum case
A. Lange & Söhne
Datograph
Ref. 403.035
Glashütte Original PanoMaticLunar (Steel, Silver Dial) Ref. 1-90-02-42-32-61, silver dial, steel case
Glashütte Original
PanoMaticLunar
Ref. 1-90-02-42-32-61
IWC Portugieser Chronograph Ref. IW371446, silver dial, steel case
IWC
Portugieser
Ref. IW371446
Vacheron Constantin Patrimony Self-Winding Ref. 85180/000R-9166, silver dial, gold-rose case
Vacheron Constantin
Patrimony
Ref. 85180/000R-9166

Buying guidance

← Back to Grail Atlas